Belling Fan Oven Elements, Belling Grill Elements, Belling Cooker Elements
Cooker Elements Section for Belling Oven and Grill Elements 
Belling are one of the oldest brands of electric cookers, and they are still in production today. So thats why we stock a very large range of Belling oven elements, from the old to the new we have most Belling cooker elements in stock, If we don't then we endeavor to order them in and dispatch it with 5 working days. Most Belling oven and grill elements are easy to fit so why not take the plung, buy the Belling oven elements youself and within 30 minutes your oven will be heating up like new again.
Belling Oven and Grill Elements (Total Products 12, Showing: 9 -> 12)
Genuine Spare Part
Belling Oven Element
Top Oven Base Element 1200 watt
Center bolt fixing
Belling Cooker models to fit
058599279, 058599281, 058599282, 058599283, 058599284, 058599285, 058599286,
Classic,
Format,
F...
Belling Oven Element
Top Oven Base Element 1200 watt
Center bolt fixing
Belling Cooker models to fit
058599279, 058599281, 058599282, 058599283, 058599284, 058599285, 058599286,
Classic,
Format,
Finesse
...
Genuine Spare Part
Part No, 082620838
Fan Oven Element to Fit Belling Cookers
1800 watt
Tags 23 mm
Width 190mm
Height 223mm
This part fits the following belling models
050534018
050534019
050561071
...
Genuine Spare Part
Belling Oven Side Element 1200 watts
Fits both R/H AND L/H
Length 375 mm
Width 240 mm
Bracket 70 mm
Tags: 40 mm
Part No C00233876 was 6224700
Belling Cooker models to fit
204BR, 206BH, 301, Forum, 315
Belling Oven Elements and Belling Grill Elements
Belling Fan Ovens - Built-In or Free Standing Belling Cookers
The heating element which produces the heat to maintain a cooking temperature in an oven is installed in the rear of a oven box in a circular form around the oven fan blade which distributes the hot air round the oven to produce an even cooking temperature over the whole of the oven with cooking times being reduced in a fan oven
All Belling oven fan motors should turn all the while the oven is turned on, failure of the oven fan to turn at full speed will result in poor cooking results and can cause the element to fail
Power to the oven elements is controlled either mechanically by turning a temperture dial or thermostat contol or electronically by a timer control panel.When an oven fails to come on you should always first check the auto clock to ensure this is set correctly, needs to be on a manual setting for the oven to come on
Oven fan elements have a fairly high rate of failure and will often cause the electrical supply to trip or to blow a fuse, failure is also sometimes accompanied by a covering of white powder substance over the oven caused by a split in the metal covering of the element
Most elements are fitted from inside the oven compartment and can reached by removing the covering plate from back of the compartment, however some elements are retained to the rear of the oven by threaded studs from the element bracket and retained by nuts which means the element is only removable by access to the rear of the oven box
Ensure that when replacing an Belling Oven Element that the fixings for the element are secure and tight, failure to secure the element can result in this touching the fan blade which make the oven very noisy but also can damage the element which can shorten its life, be also very careful if spraying the oven with an oven cleaner to make sure that this does not come into contact with the element, this will again damage the element surface which will reduce its life
Belling Ovens - Built-In or Free Standing with conventional heating elements and Fan heating elements
These ovens use a base element which is fitted under bottom of the main oven box together with the outer ring of the the grill element to provide heat for conventional heating ovens,
Belling oven base elements can only be accessed from the rear of the oven but the grill may in some cases be able to be changed from inside the the oven box by removal of screws from the fixing bracket, be aware that when extracting the element it will have connecting wires attached, other may have stud fixing which again will have to removed from the rear of the cooker.
Changing a Belling element should only be undertaken by a qualified or competent person with the electric supply disconnected